The words you meet on spec sheets, quotes and boxes, explained once. Product pages link here from their specification labels, and each guide lists the terms it uses.
Floor types
- Engineered wood
-
A real hardwood top layer (the lamella or wear layer, often 2–6 mm) bonded to a plywood or softwood core. More stable than solid wood in changing humidity; a thicker top layer can be sanded more times.
- HDF (high-density fibreboard)
-
A dense board made of wood fibres pressed with resin. It is the core of laminate flooring and of some engineered boards. Denser HDF holds a click joint better and resists denting, but it is still sensitive to water.
- Laminate
-
A floor plank with an HDF core, a printed decor paper and a hard melamine overlay. Its abrasion resistance is classed AC1–AC5 under EN 13329. The HDF core is wood-based, so standing water at the joints can make it swell.
- LVT (luxury vinyl tile / plank)
-
Multi-layer vinyl flooring with a printed decor and a clear wear layer. Thin LVT is glued down (dry-back) on a smooth screed; thicker LVT has a click joint and floats. More flexible than SPC, so it shows subfloor bumps more readily.
- SPC (stone plastic composite)
-
A rigid vinyl plank: a core of limestone powder bound with PVC and stabilisers, a printed decor film and a clear wear layer on top. The core contains no wood fibre, so it does not swell when wet; joints and the subfloor still need care. Usually clicked together as a floating floor.
- WPC (wood plastic composite)
-
The term is used for two different products. In decking, WPC boards are an extruded mix of wood flour and plastic for outdoor use. In vinyl flooring, a "WPC" plank has a foamed PVC core that is lighter and softer underfoot than SPC.
Ratings & standards
- AC rating (abrasion class)
-
The EN 13329 class for laminate, from AC1 to AC5, based on an abrasion test of the surface. AC3 suits all rooms in a home, AC4 general commercial areas and AC5 heavy commercial use. There is no AC6 or higher in EN 13329. It applies to laminate only, not to SPC or vinyl.
- Fire class (EN 13501-1)
-
The European reaction-to-fire classes for floorings, A1fl to Ffl, with a smoke class s1 or s2 — for example Bfl-s1 or Cfl-s1. A product page shows a fire class only with the test report behind it.
- Formaldehyde class (E1 / E0)
-
Emission classes for wood-based boards such as HDF and plywood. E1 is the European limit (EN 717-1 chamber test, 0.1 ppm). "E0" is a stricter label with no single European definition, so ask which test and limit it refers to.
- Slip rating (R9–R13)
-
The DIN 51130 ramp-test classes for shod feet, from R9 (lowest) to R13 (highest slip resistance). Other tests, such as the pendulum test, use different scales.
- Use class (EN ISO 10874)
-
A two-digit class for where a floor can be used: 21–23 domestic (light to heavy), 31–34 commercial and 41–43 light industrial. Vinyl, SPC and laminate are classed this way; the class comes from the product's test results.
Construction
- Bevel
-
A chamfer along the plank edges (micro-bevel or a deeper V-groove) that makes each plank read separately, like real boards. Square-edge planks give a more continuous surface.
- mil
-
A thousandth of an inch (0.0254 mm), used to state wear-layer thickness: 12 mil ≈ 0.3 mm, 20 mil ≈ 0.5 mm.
- Wear layer
-
The clear top layer of a vinyl, SPC or LVT plank that protects the printed decor. It is given in millimetres or mil (1 mil = 0.0254 mm), e.g. 0.3 mm (12 mil) for homes and 0.5 mm (20 mil) or more for busier areas. A thicker wear layer lasts longer under the same traffic.
Installation
- Acclimatisation
-
Leaving the boxes in the room where they will be laid — for the time the manufacturer states, often 24–48 hours — so the planks reach the room's temperature and humidity before installation. Wood and laminate need it most.
- Click system
-
A machined joint that locks planks edge to edge without glue. "Angle-angle" joints are angled in on both sides; "drop-lock" (fold-down) short ends are pressed down. Many joint designs are licensed under brand names; we describe them by their generic type.
- Expansion gap
-
A gap left at walls, pillars, pipes and door frames (often 8–10 mm; follow the product's guide) so a floating floor can move with temperature and humidity. Skirting or profiles cover it. Long runs and doorways may need an expansion profile.
- IXPE
-
Irradiation cross-linked polyethylene: a closed-cell foam, typically 1–1.5 mm thick, often factory-attached to the back of SPC planks as an acoustic underlay.
- Moisture barrier (vapour barrier)
-
A polyethylene sheet, commonly 200 micron (0.2 mm), laid over a concrete or screed subfloor under laminate and wood floors so moisture from the slab cannot reach the planks. Joints are overlapped and taped and the sheet is turned up at the walls.
- Skirting
-
The board along the bottom of a wall. With a floating floor it covers the expansion gap and is fixed to the wall, not to the floor.
- Subfloor flatness
-
How even the surface under a new floor is. Click floors commonly need it within 3 mm over a 2 m straightedge (some products ask for more); humps are ground down and dips filled with a levelling compound before laying. Old tiles must also be firmly bonded.
- Underlay
-
A thin layer between the subfloor and a floating floor. It evens out very small irregularities and reduces footfall and impact sound; some include a moisture barrier. Planks with an attached underlay usually must not get a second one — follow the product's installation guide.
Buying
- GST on flooring
-
Goods and Services Tax added to the price. Vinyl / SPC (HSN 3918), laminate (4411) and engineered wood (4418) are at 18% under the rates in force since 22 September 2025 (Notification 9/2025-Central Tax (Rate)); installation is typically charged at 18% too. Our prices are shown excluding and including GST — confirm the rate on your invoice.
- HSN codes (3918, 4418, 4411, 4409)
-
The Harmonised System headings used on Indian GST invoices: 3918 for floor coverings of plastics (vinyl, SPC, LVT), 4411 for fibreboard such as HDF laminate, 4418 for assembled wooden flooring panels (engineered wood) and 4409 for solid wood strips. The product page shows the code we invoice under.
- Wastage allowance
-
Extra material ordered to cover cuts and offcuts: around 7% for straight laying and 15–20% for herringbone or chevron, more in small or irregular rooms. Our calculator adds it by pattern; the measured quote confirms it.
General definitions. A product page shows a rating (water, fire, slip, AC, warranty) only with the test report or terms behind it.
Missing a term? Ask us and we will add it.